Kategorije izdelkov

Ročaj nogavic za vlečenje kabla

Kratek opis:

Podjetje za dviganje vrvi proizvaja Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.

Steel wire mesh cable pulling socks for cables, pipes and ducts. Cable Ø 9–160 mm, mesh length 300–1500 mm, enojno ali dvojno oko. Tovarniško neposredno od podjetja Lift sling rigging.

Podrobnosti o izdelku

Podjetje za dviganje vrvi proizvaja Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.

Lifet cable pulling socks — also called wire mesh pulling grips, cable socks, cable pulling grips or mesh grips — are flexible steel wire mesh sleeves that grip a cable, pipe or duct rod tightly while you pull it. The mesh tightens around the load as tension rises, so a pulling sock needs no clamps, bolts or tools: slide it on, potegni, and the grip locks on. Every sock is braided in our own factory from galvanised steel wire, z enim očesom, double eye or flexible eye options, for cable diameters from 9 mm do 160 mm.

What Is a Cable Pulling Sock?

A cable pulling sock is a tubular, double-layer woven wire mesh that slips over the end of a cable and grips it by friction alone. The open end of the mesh closes on the cable, the closed end carries a braided eye or swaged eye, and the pulling line is attached to that eye. Because the grip increases with the pull, the sock holds the cable without crushing the insulation, the conductor or the pipe wall.

Typical names for the same tool in different trades: nogavica za vlečenje kabla, oprijem za vlečenje žične mreže, kabelska nogavica, pulling grip, mesh grip, wire grip, kabelska nogavica, support grip and Kellems-style grip.

Cable Pulling Socks
Lift sling rigging company produce Cable Pulling Socks

How a Wire Mesh Cable Pulling Grip Works

  • Slide on — the mesh is expanded and pushed over the cable end. It must be long enough to cover the whole gripping length, ne le konice kabla.
  • Grip — as the pulling line tensions the eye, the weave contracts radially. Pulling force is converted into a uniform radial clamping force along the entire mesh length, so the load is spread over a long section of cable instead of one point.
  • Release — slacken the line and push the mesh forward; the weave opens and the sock slides off. Brez orodja, no damage to the cable jacket.

The same principle lets a pulling sock be used to lift, hold or support a smooth cylindrical load — pipes, ducts, conduit bundles, rods, cable drums and hoses.

Key Features of Lift Cable Pulling Socks

  • Galvanised steel wire mesh — high-tensile, corrosion-resistant wire braided in a double-layer cross weave; AISI 304 / 316 stainless steel available on request.
  • Grip increases with load — no clamp, no bolt, no cable deformation; ideal for fragile insulation, lead sheaths, fibre and copper.
  • Eno oko, double eye or flexible eye — braided rope eye, swaged aluminium ferrule eye, rotating eye and offset eye versions.
  • Wide size range — cable diameter 9–160 mm, mesh length 300–1500 mm as standard; longer and larger sizes made to order.
  • Optional protective coating — PVC / rubber coated mesh for painted, stainless or polished pipe where surface marking must be avoided.
  • OEM and private label — your logo, dolžina očesa, eye type and packing; factory-direct pricing and fast lead time from Jiangsu, Kitajska.

Tipične aplikacije

  • Vlečenje LV, MV and HV power cables, control and fibre optic cable through ducts and trenches
  • Vlečenje kabelskih snopov, wire ropes and rods with cable winches and pullers
  • Ravnanje z jeklenimi cevmi, PVC/PE cev, vodnik, cev in kanal
  • Supporting or lowering smooth cylindrical loads where clamps or hooks must not mark the surface
  • Telekom, uporabnost, offshore and tunnel installation work

Cable Pulling Sock Specifications

Standard specification of Lifet cable pulling socks / wire mesh pulling grips

Selection chart (cable diameter → sock size)

Values are typical for the standard galvanised range. Final capacity depends on cable surface, mesh length and number of layers — please confirm the rating for your application with our engineers before use.

How to Select the Right Cable Pulling Sock

  • Measure the outside diameter of the cable, pipe or bundle at the point it will be gripped — not the nominal size. For bundles, uporabite celotni premer.
  • Check the diameter range — a sock must be expanded to grip, so choose a model whose range covers your measured diameter. Too large will slip, premajhen ne bo drsel.
  • Match the mesh length to the load — longer socks spread the grip and support higher pulling forces; as a rule, use at least 4–5 × the cable diameter of mesh engagement.
  • Choose the eye type — single eye for straight pulls, dvojno / flexible eye where the line must swivel, rotating eye for long duct runs.
  • Consider the surface — for painted, stainless or plastic pipe, choose a PVC or rubber coated mesh to prevent marking.

Namestitev & Varna uporaba

  • Preglejte mrežo, oko in obroč pred vsako uporabo; discard any sock with broken wires, deformiranega očesa ali zdrsnjenega obroča.
  • Expand the mesh fully and slide it on until the cable end reaches the eye — never pull with the cable only half inserted.
  • Poteg naj bo poravnan z osjo mreže; side loading reduces capacity and can damage the weave.
  • Nikoli ne prekoračite nazivne vlečne zmogljivosti, and never use a cable pulling sock for overhead lifting unless the model has been rated and marked for lifting use.
  • Hraniti na suhem in čistem; wipe and re-check galvanised socks after use in wet or salty environments.
  • Double Eye Split Mesh Lace Closing Support Grips
    Lift sling rigging company produce Double Eye Split Mesh Lace Closing Support Grips

Quality Control at Lift

Lift Sling Rigging Co., Ltd has produced wire rope and mesh rigging in Taizhou, Jiangsu že skoraj trideset let. Each cable pulling sock is braided from wire we select, oko je prepleteno ali zavihano na nadzorovano dolžino, in vzorci so pred odpremo testirani. Na zahtevo je mogoče organizirati poročila o inšpekcijskih pregledih pred odpremo in testiranje tretje osebe.

Pogosto zastavljena vprašanja

What is a cable pulling sock used for?

Oprime kabel, cev, rod or duct so it can be pulled with a winch or by hand. The wire mesh tightens as tension rises, which spreads the gripping force along the cable and avoids clamps that could crush or mark it.

How do I choose the correct size?

Measure the true outer diameter of the cable or bundle and pick the model whose range covers it, then choose the mesh length from the pulling load. Our selection chart above gives standard models from 9 mm do 160 mm.

Single eye or double eye — what is the difference?

A single eye has one braided loop for a straight pull. A double or flexible eye gives two loops (or a swivel point) so the sock can align with the winch line in bends, manholes and long duct runs.

Can the mesh be stainless steel or coated?

ja. Standardna je pocinkana žica; AISI 304 oz 316 stainless steel is available for corrosive or offshore work, and PVC or rubber coated mesh is available where the cable or pipe surface must not be marked.

Kaj je varnostni faktor?

Standard socks are rated at a 5:1 varnostni faktor na pretržno trdnost. Tell us your required pulling load and we will specify the mesh wire diameter and length to suit.

Can you make custom lengths and put our brand on it?

Yes — custom mesh lengths up to 3000 mm, custom eye types, colour coding and your own logo or private label packing are all produced to order at our factory.

Request a Cable Pulling Sock Quotation

Send us your cable diameter, dolžina očesa, vrsto očesa in potrebno vlečno obremenitev, and our engineers will confirm the correct model and price within one working day.

Telefon / WhatsApp: +86 180 6600 2268 E-pošta: 702461526@qq.com Naslov: Industrijski park Lifute, Mesto Taizhou, Provinca Jiangsu, Kitajska

Sorodni izdelki

  • Zanke za žične vrvi — celoten obseg
  • Lifting slings and lifting belts
  • Cargo nets and lifting nets
  • Contact Lifet for a quotation
Parameter Specifikacija
Ime izdelka Nogavica za vlečenje kabla / oprijem za vlečenje žične mreže / cable pulling grip
Material Pocinkana visokonatezna jeklena žica (AISI 304 / 316 neobvezno iz nerjavečega jekla)
Struktura Double-layer cross-woven tubular mesh with braided or swaged eye
Premer mrežne žice 1.5 mm / 2.0 mm / 2.5 mm / 3.0 mm (izbran glede na premer kabla in vlečno obremenitev)
Razpon premera kabla 9–16 mm do 130–160 mm v standardnih modelih; večje velikosti po naročilu
Mreža (nogavica) dolžina 300 mm, 450 mm, 600 mm, 900 mm, 1200 mm, 1500 mm; po meri do 3000 mm
Oko / vrsta glave Eno oko, dvojno oko, gibljivo oko, vrtljivo oko, offset oko
Prileganje očesu Braided rope eye or swaged aluminium ferrule (tanek, nizek profil gradnje)
Pretržna trdnost Model dependent — see selection chart below
Varnostni faktor 5:1 na nazivno pretržno trdnost
Možnosti premazovanja Navadno pocinkano; PVC / rubber coated mesh; coloured coating for coding
Delovna temperatura –40 °C do +120 °C (prevlečene različice do +70 °C)
Prilagajanje Dolžina mreže po meri, oko po meri, tisk logotipa, zasebno etiketno pakiranje
Izvor Lift Sling Rigging Co., Ltd — Taizhou, Jiangsu, Kitajska

 

Model Razpon Ø kabla (mm) Dolžina očesa (mm) Žična mreža Ø (mm) Vlečna zmogljivost (kg)
CPS-16 9–16 300 1.5 750
CPS-25 16–25 450 2.0 1,300
CPS-38 25–38 600 2.0 1,800
CPS-50 38–50 700 2.5 2,500
CPS-75 50–75 900 2.5 3,500
CPS-100 75–100 1200 3.0 5,000
CPS-160 130–160 1500 3.0 8,000

Pustite svoje sporočilo

Pomaknite se na vrh