Empresa de aparelhamento de sling de elevação produz meias para puxar cabos,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.
Lifet cable pulling socks — also called wire mesh pulling grips, meias de cabo, cable pulling grips or mesh grips — are flexible steel wire mesh sleeves that grip a cable, pipe or duct rod tightly while you pull it. The mesh tightens around the load as tension rises, so a pulling sock needs no clamps, bolts or tools: slide it on, puxar, and the grip locks on. Every sock is braided in our own factory from galvanised steel wire, com um único olho, double eye or flexible eye options, for cable diameters from 9 mm para 160 milímetros.
What Is a Cable Pulling Sock?
A cable pulling sock is a tubular, double-layer woven wire mesh that slips over the end of a cable and grips it by friction alone. The open end of the mesh closes on the cable, the closed end carries a braided eye or swaged eye, and the pulling line is attached to that eye. Because the grip increases with the pull, the sock holds the cable without crushing the insulation, the conductor or the pipe wall.
Typical names for the same tool in different trades: meia puxando cabo, malha de arame puxando aperto, meia de cabo, pulling grip, mesh grip, wire grip, meia de cabo, support grip and Kellems-style grip.

How a Wire Mesh Cable Pulling Grip Works
- Slide on — the mesh is expanded and pushed over the cable end. It must be long enough to cover the whole gripping length, não apenas a ponta do cabo.
- Grip — as the pulling line tensions the eye, the weave contracts radially. Pulling force is converted into a uniform radial clamping force along the entire mesh length, so the load is spread over a long section of cable instead of one point.
- Release — slacken the line and push the mesh forward; the weave opens and the sock slides off. No tools, no damage to the cable jacket.
The same principle lets a pulling sock be used to lift, hold or support a smooth cylindrical load — pipes, ducts, conduit bundles, rods, cable drums and hoses.
Key Features of Lift Cable Pulling Socks
- Galvanised steel wire mesh — high-tensile, corrosion-resistant wire braided in a double-layer cross weave; AISI 304 / 316 stainless steel available on request.
- Grip increases with load — no clamp, no bolt, no cable deformation; ideal for fragile insulation, lead sheaths, fibre and copper.
- Olho único, double eye or flexible eye — braided rope eye, swaged aluminium ferrule eye, rotating eye and offset eye versions.
- Wide size range — cable diameter 9–160 mm, mesh length 300–1500 mm as standard; longer and larger sizes made to order.
- Optional protective coating — PVC / rubber coated mesh for painted, stainless or polished pipe where surface marking must be avoided.
- OEM and private label — your logo, comprimento da malha, eye type and packing; factory-direct pricing and fast lead time from Jiangsu, China.
Aplicações Típicas
- Puxando LV, MV and HV power cables, control and fibre optic cable through ducts and trenches
- Puxando feixes de cabos, wire ropes and rods with cable winches and pullers
- Manuseio de tubos de aço, Tubo de PVC/PE, conduíte, mangueira e duto
- Supporting or lowering smooth cylindrical loads where clamps or hooks must not mark the surface
- Telecomunicações, utilidade, offshore and tunnel installation work
Cable Pulling Sock Specifications
Standard specification of Lifet cable pulling socks / wire mesh pulling grips
Selection chart (cable diameter → sock size)
Values are typical for the standard galvanised range. Final capacity depends on cable surface, mesh length and number of layers — please confirm the rating for your application with our engineers before use.
How to Select the Right Cable Pulling Sock
- Measure the outside diameter of the cable, pipe or bundle at the point it will be gripped — not the nominal size. For bundles, use the overall diameter.
- Check the diameter range — a sock must be expanded to grip, so choose a model whose range covers your measured diameter. Too large will slip, too small will not slide on.
- Match the mesh length to the load — longer socks spread the grip and support higher pulling forces; as a rule, use at least 4–5 × the cable diameter of mesh engagement.
- Choose the eye type — single eye for straight pulls, dobro / flexible eye where the line must swivel, rotating eye for long duct runs.
- Consider the surface — for painted, stainless or plastic pipe, choose a PVC or rubber coated mesh to prevent marking.
Instalação & Uso Seguro
- Inspecione a malha, olho e ponteira antes de cada uso; discard any sock with broken wires, a deformed eye or a slipped ferrule.
- Expand the mesh fully and slide it on until the cable end reaches the eye — never pull with the cable only half inserted.
- Mantenha a tração alinhada com o eixo da malha; side loading reduces capacity and can damage the weave.
- Nunca exceda a capacidade de tração nominal, and never use a cable pulling sock for overhead lifting unless the model has been rated and marked for lifting use.
- Armazene seco e limpo; wipe and re-check galvanised socks after use in wet or salty environments.
-

Lift sling rigging company produce Double Eye Split Mesh Lace Closing Support Grips
Quality Control at Lift
Lift Sling Rigging Co., Ltd has produced wire rope and mesh rigging in Taizhou, Jiangsu por quase trinta anos. Each cable pulling sock is braided from wire we select, o olho é trançado ou estampado em um comprimento controlado, e as amostras são testadas antes do envio. Relatórios de inspeção pré-embarque e testes de terceiros podem ser organizados mediante solicitação.
Perguntas frequentes
What is a cable pulling sock used for?
It grips a cable, cano, rod or duct so it can be pulled with a winch or by hand. The wire mesh tightens as tension rises, which spreads the gripping force along the cable and avoids clamps that could crush or mark it.
How do I choose the correct size?
Measure the true outer diameter of the cable or bundle and pick the model whose range covers it, then choose the mesh length from the pulling load. Our selection chart above gives standard models from 9 mm para 160 milímetros.
Single eye or double eye — what is the difference?
A single eye has one braided loop for a straight pull. A double or flexible eye gives two loops (or a swivel point) so the sock can align with the winch line in bends, manholes and long duct runs.
Can the mesh be stainless steel or coated?
Sim. Galvanised wire is standard; AISI 304 ou 316 stainless steel is available for corrosive or offshore work, and PVC or rubber coated mesh is available where the cable or pipe surface must not be marked.
Qual é o fator de segurança?
Standard socks are rated at a 5:1 fator de segurança na resistência à ruptura. Tell us your required pulling load and we will specify the mesh wire diameter and length to suit.
Can you make custom lengths and put our brand on it?
Yes — custom mesh lengths up to 3000 milímetros, custom eye types, colour coding and your own logo or private label packing are all produced to order at our factory.
Request a Cable Pulling Sock Quotation
Send us your cable diameter, comprimento da malha, tipo de olho e carga de tração necessária, and our engineers will confirm the correct model and price within one working day.
Telefone / WhatsApp: +86 180 6600 2268 E-mail: 702461526Endereço @qq.com: Parque Industrial Lifute, Cidade de Taizhou, Província de Jiangsu, China
Produtos relacionados
- Eslingas de cabo de aço – linha completa
- Lifting slings and lifting belts
- Cargo nets and lifting nets
- Contact Lifet for a quotation
| Parâmetro | Especificação |
| Nome do produto | Meia para puxar cabo / malha de arame puxando aperto / cable pulling grip |
| Material | Fio de aço galvanizado de alta resistência (AISI 304 / 316 aço inoxidável opcional) |
| Estrutura | Double-layer cross-woven tubular mesh with braided or swaged eye |
| Diâmetro do fio de malha | 1.5 milímetros / 2.0 milímetros / 2.5 milímetros / 3.0 milímetros (selecionado pelo diâmetro do cabo e carga de tração) |
| Faixa de diâmetro do cabo | 9–16 mm até 130–160 mm em modelos padrão; tamanhos maiores feitos sob encomenda |
| Malha (peúga) comprimento | 300 milímetros, 450 milímetros, 600 milímetros, 900 milímetros, 1200 milímetros, 1500 milímetros; personalizado até 3000 milímetros |
| Olho / tipo de cabeça | Olho único, olho duplo, olho flexível, olho giratório, olho deslocado |
| Encaixe nos olhos | Braided rope eye or swaged aluminium ferrule (afinar, perfil de baixo acúmulo) |
| Força de ruptura | Model dependent — see selection chart below |
| Fator de segurança | 5:1 na resistência nominal à ruptura |
| Opções de revestimento | Galvanizado simples; PVC / rubber coated mesh; coloured coating for coding |
| Temperatura de trabalho | −40 °C a +120 °C (versões revestidas para +70 °C) |
| Personalização | Comprimento de malha personalizado, custom eye, impressão do logotipo, embalagem de marca própria |
| Origem | Lift Sling Rigging Co., Ltd – Taizhou, Jiangsu, China |
| Modelo | Faixa de Ø do cabo (milímetros) | Comprimento da malha (milímetros) | Arame de malha Ø (milímetros) | Capacidade de extração (kg) |
| CPS-16 | 9–16 | 300 | 1.5 | 750 |
| CPS-25 | 16–25 | 450 | 2.0 | 1,300 |
| CPS-38 | 25–38 | 600 | 2.0 | 1,800 |
| CPS-50 | 38–50 | 700 | 2.5 | 2,500 |
| CPS-75 | 50–75 | 900 | 2.5 | 3,500 |
| CPS-100 | 75–100 | 1200 | 3.0 | 5,000 |
| CPS-160 | 130–160 | 1500 | 3.0 | 8,000 |



