ປະເພດຜະລິດຕະພັນ

Cable Pulling Socks Grip

ລາຍລະອຽດສັ້ນ:

ບໍລິສັດ Lift sling rigging ຜະລິດ Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.

Steel wire mesh cable pulling socks for cables, pipes and ducts. Cable Ø 9–160 mm, mesh length 300–1500 mm, ຕາດຽວ ຫຼືສອງຕາ. Factory-direct from Lift sling rigging company.

ລາຍລະອຽດຜະລິດຕະພັນ

ບໍລິສັດ Lift sling rigging ຜະລິດ Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.

Lifet cable pulling socks — also called wire mesh pulling grips, ຖົງຕີນສາຍ, cable pulling grips or mesh grips — are flexible steel wire mesh sleeves that grip a cable, pipe or duct rod tightly while you pull it. The mesh tightens around the load as tension rises, so a pulling sock needs no clamps, bolts or tools: slide it on, pull, and the grip locks on. Every sock is braided in our own factory from galvanised steel wire, ດ້ວຍຕາດຽວ, double eye or flexible eye options, for cable diameters from 9 mm ເຖິງ 160 ມມ.

What Is a Cable Pulling Sock?

A cable pulling sock is a tubular, double-layer woven wire mesh that slips over the end of a cable and grips it by friction alone. The open end of the mesh closes on the cable, the closed end carries a braided eye or swaged eye, and the pulling line is attached to that eye. Because the grip increases with the pull, the sock holds the cable without crushing the insulation, the conductor or the pipe wall.

Typical names for the same tool in different trades: ຖົງຕີນດຶງສາຍ, ຕາຫນ່າງສາຍດຶງຈັບ, ຖົງຕີນສາຍ, pulling grip, mesh grip, wire grip, ຫຼັກຊັບສາຍ, support grip and Kellems-style grip.

Cable Pulling Socks
Lift sling rigging company produce Cable Pulling Socks

How a Wire Mesh Cable Pulling Grip Works

  • Slide on — the mesh is expanded and pushed over the cable end. It must be long enough to cover the whole gripping length, ບໍ່ພຽງແຕ່ປາຍສາຍ.
  • Grip — as the pulling line tensions the eye, the weave contracts radially. Pulling force is converted into a uniform radial clamping force along the entire mesh length, so the load is spread over a long section of cable instead of one point.
  • Release — slacken the line and push the mesh forward; the weave opens and the sock slides off. ບໍ່ມີເຄື່ອງມື, no damage to the cable jacket.

The same principle lets a pulling sock be used to lift, hold or support a smooth cylindrical load — pipes, ducts, conduit bundles, rods, cable drums and hoses.

Key Features of Lift Cable Pulling Socks

  • Galvanised steel wire mesh — high-tensile, corrosion-resistant wire braided in a double-layer cross weave; AISI 304 / 316 stainless steel available on request.
  • Grip increases with load — no clamp, no bolt, no cable deformation; ideal for fragile insulation, lead sheaths, fibre and copper.
  • ຕາດຽວ, double eye or flexible eye — braided rope eye, swaged aluminium ferrule eye, rotating eye and offset eye versions.
  • Wide size range — cable diameter 9–160 mm, mesh length 300–1500 mm as standard; longer and larger sizes made to order.
  • Optional protective coating — PVC / rubber coated mesh for painted, stainless or polished pipe where surface marking must be avoided.
  • OEM and private label — your logo, ຄວາມຍາວຕາຫນ່າງ, eye type and packing; factory-direct pricing and fast lead time from Jiangsu, ຈີນ.

ຄໍາຮ້ອງສະຫມັກທົ່ວໄປ

  • ດຶງ LV, MV and HV power cables, control and fibre optic cable through ducts and trenches
  • ດຶງຊຸດສາຍ, wire ropes and rods with cable winches and pullers
  • ການຈັດການທໍ່ເຫລໍກ, ທໍ່ PVC / PE, ທໍ່ນ້ຳ, ທໍ່ແລະທໍ່
  • Supporting or lowering smooth cylindrical loads where clamps or hooks must not mark the surface
  • ໂທລະຄົມ, ປະໂຫຍດ, offshore and tunnel installation work

Cable Pulling Sock Specifications

Standard specification of Lifet cable pulling socks / wire mesh pulling grips

Selection chart (cable diameter → sock size)

Values are typical for the standard galvanised range. Final capacity depends on cable surface, mesh length and number of layers — please confirm the rating for your application with our engineers before use.

How to Select the Right Cable Pulling Sock

  • Measure the outside diameter of the cable, pipe or bundle at the point it will be gripped — not the nominal size. For bundles, ໃຊ້ເສັ້ນຜ່າສູນກາງລວມ.
  • Check the diameter range — a sock must be expanded to grip, so choose a model whose range covers your measured diameter. Too large will slip, ຂະຫນາດນ້ອຍເກີນໄປຈະບໍ່ເລື່ອນໃສ່.
  • Match the mesh length to the load — longer socks spread the grip and support higher pulling forces; as a rule, use at least 4–5 × the cable diameter of mesh engagement.
  • Choose the eye type — single eye for straight pulls, ສອງເທົ່າ / flexible eye where the line must swivel, rotating eye for long duct runs.
  • Consider the surface — for painted, stainless or plastic pipe, choose a PVC or rubber coated mesh to prevent marking.

ການຕິດຕັ້ງ & ການນໍາໃຊ້ທີ່ປອດໄພ

  • ກວດກາຕາຫນ່າງ, ຕາແລະ ferrule ກ່ອນທີ່ຈະນໍາໃຊ້ທຸກຄັ້ງ; discard any sock with broken wires, ຕາເສື່ອມ ຫຼື ເປື່ອຍ.
  • Expand the mesh fully and slide it on until the cable end reaches the eye — never pull with the cable only half inserted.
  • ຮັກສາການດຶງໃຫ້ສອດຄ່ອງກັບແກນຕາຫນ່າງ; side loading reduces capacity and can damage the weave.
  • ບໍ່ເຄີຍເກີນຄວາມສາມາດດຶງລະດັບ, and never use a cable pulling sock for overhead lifting unless the model has been rated and marked for lifting use.
  • ເກັບຮັກສາແຫ້ງແລະສະອາດ; wipe and re-check galvanised socks after use in wet or salty environments.
  • Double Eye Split Mesh Lace Closing Support Grips
    Lift sling rigging company produce Double Eye Split Mesh Lace Closing Support Grips

Quality Control at Lift

Lift Sling Rigging Co., Ltd has produced wire rope and mesh rigging in Taizhou, Jiangsu ເກືອບສາມສິບປີ. Each cable pulling sock is braided from wire we select, ຕາແມ່ນ braided ຫຼື swaged ກັບຄວາມຍາວຄວບຄຸມ, ແລະຕົວຢ່າງແມ່ນຫຼັກຖານສະແດງກ່ອນການຈັດສົ່ງ. ບົດລາຍງານການກວດກາກ່ອນການຂົນສົ່ງແລະການທົດສອບພາກສ່ວນທີສາມສາມາດໄດ້ຮັບການຈັດລຽງຕາມການຮ້ອງຂໍ.

ຄໍາຖາມທີ່ຖາມເລື້ອຍໆ

What is a cable pulling sock used for?

ມັນຈັບສາຍ, ທໍ່, rod or duct so it can be pulled with a winch or by hand. The wire mesh tightens as tension rises, which spreads the gripping force along the cable and avoids clamps that could crush or mark it.

How do I choose the correct size?

Measure the true outer diameter of the cable or bundle and pick the model whose range covers it, then choose the mesh length from the pulling load. Our selection chart above gives standard models from 9 mm ເຖິງ 160 ມມ.

Single eye or double eye — what is the difference?

A single eye has one braided loop for a straight pull. A double or flexible eye gives two loops (or a swivel point) so the sock can align with the winch line in bends, manholes and long duct runs.

Can the mesh be stainless steel or coated?

ແມ່ນແລ້ວ. ສາຍ Galvanized ແມ່ນມາດຕະຖານ; AISI 304 ຫຼື 316 stainless steel is available for corrosive or offshore work, and PVC or rubber coated mesh is available where the cable or pipe surface must not be marked.

ປັດໄຈຄວາມປອດໄພແມ່ນຫຍັງ?

Standard socks are rated at a 5:1 ປັດໄຈຄວາມປອດໄພກ່ຽວກັບຄວາມເຂັ້ມແຂງ breaking. Tell us your required pulling load and we will specify the mesh wire diameter and length to suit.

Can you make custom lengths and put our brand on it?

Yes — custom mesh lengths up to 3000 ມມ, custom eye types, colour coding and your own logo or private label packing are all produced to order at our factory.

Request a Cable Pulling Sock Quotation

Send us your cable diameter, ຄວາມຍາວຕາຫນ່າງ, ປະເພດຕາແລະການໂຫຼດດຶງທີ່ຕ້ອງການ, and our engineers will confirm the correct model and price within one working day.

ໂທລະສັບ / WhatsApp: +86 180 6600 2268 ອີເມລ: 702461526@qq.com ທີ່ຢູ່: ສວນອຸດສາຫະ ກຳ Lifute, ເມືອງ Taizhou, ແຂວງຈຽງຊູ, ຈີນ

ຜະລິດຕະພັນທີ່ກ່ຽວຂ້ອງ

  • ສາຍເຊືອກສາຍ - ເຕັມຮູບແບບ
  • Lifting slings and lifting belts
  • Cargo nets and lifting nets
  • Contact Lifet for a quotation
ພາລາມິເຕີ ຂໍ້ມູນຈໍາເພາະ
ຊື່ຜະລິດຕະພັນ ສາຍດຶງຖົງຕີນ / ຕາຫນ່າງສາຍດຶງຈັບ / cable pulling grip
ວັດສະດຸ galvanized ສາຍເຫຼັກ tensile ສູງ (AISI 304 / 316 ສະແຕນເລດທາງເລືອກ)
ໂຄງສ້າງ Double-layer cross-woven tubular mesh with braided or swaged eye
ຕາຫນ່າງເສັ້ນຜ່າສູນກາງ 1.5 ມມ / 2.0 ມມ / 2.5 ມມ / 3.0 ມມ (ເລືອກໂດຍເສັ້ນຜ່າສູນກາງຂອງສາຍເຄເບີ້ນແລະການໂຫຼດດຶງ)
ໄລຍະເສັ້ນຜ່າສູນກາງຂອງສາຍ 9–16 mm ເຖິງ 130–160 mm ໃນ​ແບບ​ມາດ​ຕະ​ຖານ​; ຂະໜາດໃຫຍ່ກວ່າຕາມສັ່ງ
ຕາຫນ່າງ (ຖົງຕີນ) ຄວາມຍາວ 300 ມມ, 450 ມມ, 600 ມມ, 900 ມມ, 1200 ມມ, 1500 ມມ; ກໍານົດເອງເຖິງ 3000 ມມ
ຕາ / ປະເພດຫົວ ຕາດຽວ, ຕາສອງເທົ່າ, ຕາທີ່ຍືດຫຍຸ່ນ, ຕາ rotating, ຕາຊົດເຊີຍ
ເຫມາະກັບຕາ Braided rope eye or swaged aluminium ferrule (ບາງໆ, ໂປຣໄຟລ໌ການກໍ່ສ້າງຕໍ່າ)
ແຮງແຕກ Model dependent — see selection chart below
ປັດໄຈຄວາມປອດໄພ 5:1 ກ່ຽວກັບຄວາມເຂັ້ມແຂງ breaking ຈັດອັນດັບ
ທາງເລືອກໃນການເຄືອບ ສັງກະສີທໍາມະດາ; PVC / rubber coated mesh; coloured coating for coding
ອຸນຫະພູມເຮັດວຽກ −40°C ເຖິງ +120 °C (ສະບັບ coated ກັບ +70 °C)
ການປັບແຕ່ງ ຄວາມຍາວຕາຫນ່າງທີ່ກໍາຫນົດເອງ, ຕາ custom, ພິມໂລໂກ້, ການຫຸ້ມຫໍ່ປ້າຍສ່ວນຕົວ
ຕົ້ນກໍາເນີດ Lift Sling Rigging Co., Ltd — Taizhou​, ຈຽງຊູ, ຈີນ

 

ຕົວແບບ ສາຍ Ø ໄລຍະ (ມມ) ຄວາມຍາວຕາຫນ່າງ (ມມ) ຕາຫນ່າງສາຍ Ø (ມມ) ຄວາມສາມາດໃນການດຶງ (ກິໂລ)
CPS-16 9–16 300 1.5 750
CPS-25 16–25 450 2.0 1,300
CPS-38 25–38 600 2.0 1,800
CPS-50 38–50 700 2.5 2,500
CPS-75 50–75 900 2.5 3,500
CPS-100 75–100 1200 3.0 5,000
CPS-160 130–160 1500 3.0 8,000

ອອກຈາກຂໍ້ຄວາມຂອງທ່ານ

ເລື່ອນໄປເທິງ