Kategori Produk

Cable Pulling Socks Grip

Katrangan singkat:

Lift sling rigging company produce Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.

Steel wire mesh cable pulling socks for cables, pipes and ducts. Cable Ø 9–160 mm, mesh length 300–1500 mm, mripat siji utawa pindho. Factory-direct from Lift sling rigging company.

Detail Produk

Lift sling rigging company produce Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.

Lifet cable pulling socks — also called wire mesh pulling grips, cable socks, cable pulling grips or mesh grips — are flexible steel wire mesh sleeves that grip a cable, pipe or duct rod tightly while you pull it. The mesh tightens around the load as tension rises, so a pulling sock needs no clamps, bolts or tools: slide it on, pull, and the grip locks on. Every sock is braided in our own factory from galvanised steel wire, kanthi mripat siji, double eye or flexible eye options, for cable diameters from 9 mm iki 160 mm.

What Is a Cable Pulling Sock?

A cable pulling sock is a tubular, double-layer woven wire mesh that slips over the end of a cable and grips it by friction alone. The open end of the mesh closes on the cable, the closed end carries a braided eye or swaged eye, and the pulling line is attached to that eye. Because the grip increases with the pull, the sock holds the cable without crushing the insulation, the conductor or the pipe wall.

Typical names for the same tool in different trades: kaos kaki tarik kabel, pegangan tarik wire mesh, cable sock, pulling grip, mesh grip, wire grip, cable stocking, support grip and Kellems-style grip.

Cable Pulling Socks
Lift sling rigging company produce Cable Pulling Socks

How a Wire Mesh Cable Pulling Grip Works

  • Slide on — the mesh is expanded and pushed over the cable end. It must be long enough to cover the whole gripping length, ora mung tip kabel.
  • Grip — as the pulling line tensions the eye, the weave contracts radially. Pulling force is converted into a uniform radial clamping force along the entire mesh length, so the load is spread over a long section of cable instead of one point.
  • Release — slacken the line and push the mesh forward; the weave opens and the sock slides off. No tools, no damage to the cable jacket.

The same principle lets a pulling sock be used to lift, hold or support a smooth cylindrical load — pipes, ducts, conduit bundles, rods, cable drums and hoses.

Key Features of Lift Cable Pulling Socks

  • Galvanised steel wire mesh — high-tensile, corrosion-resistant wire braided in a double-layer cross weave; AISI 304 / 316 stainless steel available on request.
  • Grip increases with load — no clamp, no bolt, no cable deformation; ideal for fragile insulation, lead sheaths, fibre and copper.
  • Mripat tunggal, double eye or flexible eye — braided rope eye, swaged aluminium ferrule eye, rotating eye and offset eye versions.
  • Wide size range — cable diameter 9–160 mm, mesh length 300–1500 mm as standard; longer and larger sizes made to order.
  • Optional protective coating — PVC / rubber coated mesh for painted, stainless or polished pipe where surface marking must be avoided.
  • OEM and private label — your logo, dawa bolong, eye type and packing; factory-direct pricing and fast lead time from Jiangsu, Cina.

Aplikasi Khas

  • Tarik LV, MV and HV power cables, control and fibre optic cable through ducts and trenches
  • Narik kabel bundel, wire ropes and rods with cable winches and pullers
  • Penanganan pipa baja, Pipa PVC/PE, saluran, hose and ducting
  • Supporting or lowering smooth cylindrical loads where clamps or hooks must not mark the surface
  • Telecom, utility, offshore and tunnel installation work

Cable Pulling Sock Specifications

Standard specification of Lifet cable pulling socks / wire mesh pulling grips

Selection chart (cable diameter → sock size)

Values are typical for the standard galvanised range. Final capacity depends on cable surface, mesh length and number of layers — please confirm the rating for your application with our engineers before use.

How to Select the Right Cable Pulling Sock

  • Measure the outside diameter of the cable, pipe or bundle at the point it will be gripped — not the nominal size. For bundles, nggunakake diameteripun sakabèhé.
  • Check the diameter range — a sock must be expanded to grip, so choose a model whose range covers your measured diameter. Too large will slip, cilik banget ora bakal geser ing.
  • Match the mesh length to the load — longer socks spread the grip and support higher pulling forces; as a rule, use at least 4–5 × the cable diameter of mesh engagement.
  • Choose the eye type — single eye for straight pulls, pindho / flexible eye where the line must swivel, rotating eye for long duct runs.
  • Consider the surface — for painted, stainless or plastic pipe, choose a PVC or rubber coated mesh to prevent marking.

Instalasi & Gunakake Aman

  • Inspect the mesh, eye and ferrule before every use; discard any sock with broken wires, a deformed eye or a slipped ferrule.
  • Expand the mesh fully and slide it on until the cable end reaches the eye — never pull with the cable only half inserted.
  • Keep the pull in line with the mesh axis; side loading reduces capacity and can damage the weave.
  • Aja ngluwihi kapasitas narik sing dirating, and never use a cable pulling sock for overhead lifting unless the model has been rated and marked for lifting use.
  • Simpen garing lan resik; wipe and re-check galvanised socks after use in wet or salty environments.
  • Double Eye Split Mesh Lace Closing Support Grips
    Lift sling rigging company produce Double Eye Split Mesh Lace Closing Support Grips

Quality Control at Lift

Lift Sling Rigging Co., Ltd has produced wire rope and mesh rigging in Taizhou, Jiangsu meh telung puluh taun. Each cable pulling sock is braided from wire we select, mripat wis braided utawa swaged kanggo dawa kontrol, lan conto wis dimuat sadurunge dikirim. Laporan inspeksi pra-pengiriman lan tes pihak katelu bisa diatur kanthi panyuwunan.

Pitakonan sing Sering Ditakoni

What is a cable pulling sock used for?

It grips a cable, pipa, rod or duct so it can be pulled with a winch or by hand. The wire mesh tightens as tension rises, which spreads the gripping force along the cable and avoids clamps that could crush or mark it.

How do I choose the correct size?

Measure the true outer diameter of the cable or bundle and pick the model whose range covers it, then choose the mesh length from the pulling load. Our selection chart above gives standard models from 9 mm iki 160 mm.

Single eye or double eye — what is the difference?

A single eye has one braided loop for a straight pull. A double or flexible eye gives two loops (or a swivel point) so the sock can align with the winch line in bends, manholes and long duct runs.

Can the mesh be stainless steel or coated?

ya wis. Galvanised wire is standard; AISI 304 utawa 316 stainless steel is available for corrosive or offshore work, and PVC or rubber coated mesh is available where the cable or pipe surface must not be marked.

Apa faktor safety?

Standard socks are rated at a 5:1 safety factor on the breaking strength. Tell us your required pulling load and we will specify the mesh wire diameter and length to suit.

Can you make custom lengths and put our brand on it?

Yes — custom mesh lengths up to 3000 mm, custom eye types, colour coding and your own logo or private label packing are all produced to order at our factory.

Request a Cable Pulling Sock Quotation

Send us your cable diameter, dawa bolong, jinis mripat lan beban narik sing dibutuhake, and our engineers will confirm the correct model and price within one working day.

Telpon / WhatsApp: +86 180 6600 2268 E-mail: 702461526@qq.com Alamat: Lifute Industrial Park, Kutha Taizhou, Provinsi Jiangsu, Cina

produk sing gegandhengan

  • Tali kawat slings - lengkap
  • Lifting slings and lifting belts
  • Cargo nets and lifting nets
  • Contact Lifet for a quotation
Parameter Spesifikasi
jeneng produk Cable pulling sock / pegangan tarik wire mesh / cable pulling grip
Bahan Kawat baja tegangan tinggi galvanis (AISI 304 / 316 stainless steel opsional)
Struktur Double-layer cross-woven tubular mesh with braided or swaged eye
Diameter kawat jaring 1.5 mm / 2.0 mm / 2.5 mm / 3.0 mm (dipilih dening diameteripun kabel lan narik mbukak)
Kisaran diameteripun kabel 9–16 mm nganti 130–160 mm ing model standar; ukuran luwih gedhe digawe kanggo pesenan
bolong (kaos kaki) dawa 300 mm, 450 mm, 600 mm, 900 mm, 1200 mm, 1500 mm; adat nganti 3000 mm
Mripat / jinis sirah Mripat tunggal, mripat pindho, mata fleksibel, mripat muter, mripat offset
Mripate pas Braided rope eye or swaged aluminium ferrule (tipis, profil mbangun-munggah kurang)
Kekuwatan sing rusak Model dependent — see selection chart below
Faktor keamanan 5:1 ing kekuatan bejat dirating
Pilihan lapisan Polos galvanis; PVC / rubber coated mesh; coloured coating for coding
Suhu kerja -40 °C iki +120 °C (versi ditutupi kanggo +70 °C)
Kustomisasi dawa bolong adat, custom eye, print logo, packing label pribadi
asale Lift Sling Rigging Co., Ltd - Taizhou, Jiangsu, Cina

 

Model Kabel Ø Range (mm) Dawane bolong (mm) Kawat jaring Ø (mm) Kapasitas narik (kg)
CPS-16 9–16 300 1.5 750
CPS-25 16–25 450 2.0 1,300
CPS-38 25–38 600 2.0 1,800
CPS-50 38–50 700 2.5 2,500
CPS-75 50–75 900 2.5 3,500
CPS-100 75–100 1200 3.0 5,000
CPS-160 130–160 1500 3.0 8,000

Ninggalake Pesen Panjenengan

Gulung menyang Ndhuwur