Kamfanin rigingimu na ɗaga majajjawa yana samar da Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.
Lifet cable pulling socks — also called wire mesh pulling grips, safa na USB, cable pulling grips or mesh grips — are flexible steel wire mesh sleeves that grip a cable, pipe or duct rod tightly while you pull it. The mesh tightens around the load as tension rises, so a pulling sock needs no clamps, bolts or tools: slide it on, pull, and the grip locks on. Every sock is braided in our own factory from galvanised steel wire, da ido daya, double eye or flexible eye options, for cable diameters from 9 mm ku 160 mm.
What Is a Cable Pulling Sock?
A cable pulling sock is a tubular, double-layer woven wire mesh that slips over the end of a cable and grips it by friction alone. The open end of the mesh closes on the cable, the closed end carries a braided eye or swaged eye, and the pulling line is attached to that eye. Because the grip increases with the pull, the sock holds the cable without crushing the insulation, the conductor or the pipe wall.
Typical names for the same tool in different trades: kebul ja safa, igiyoyin waya ja riko, kebul sock, pulling grip, mesh grip, wire grip, na USB safa, support grip and Kellems-style grip.

How a Wire Mesh Cable Pulling Grip Works
- Slide on — the mesh is expanded and pushed over the cable end. It must be long enough to cover the whole gripping length, not just the cable tip.
- Grip — as the pulling line tensions the eye, the weave contracts radially. Pulling force is converted into a uniform radial clamping force along the entire mesh length, so the load is spread over a long section of cable instead of one point.
- Release — slacken the line and push the mesh forward; the weave opens and the sock slides off. Babu kayan aiki, no damage to the cable jacket.
The same principle lets a pulling sock be used to lift, hold or support a smooth cylindrical load — pipes, ducts, conduit bundles, rods, cable drums and hoses.
Key Features of Lift Cable Pulling Socks
- Galvanised steel wire mesh — high-tensile, corrosion-resistant wire braided in a double-layer cross weave; AISI 304 / 316 stainless steel available on request.
- Grip increases with load — no clamp, no bolt, no cable deformation; ideal for fragile insulation, lead sheaths, fibre and copper.
- Ido ɗaya, double eye or flexible eye — braided rope eye, swaged aluminium ferrule eye, rotating eye and offset eye versions.
- Wide size range — cable diameter 9–160 mm, mesh length 300–1500 mm as standard; longer and larger sizes made to order.
- Optional protective coating — PVC / rubber coated mesh for painted, stainless or polished pipe where surface marking must be avoided.
- OEM and private label — your logo, raga tsawon, eye type and packing; factory-direct pricing and fast lead time from Jiangsu, China.
Aikace-aikace na yau da kullun
- Jawo LV, MV and HV power cables, control and fibre optic cable through ducts and trenches
- Ja na USB daure, wire ropes and rods with cable winches and pullers
- Gudanar da bututun ƙarfe, PVC / PE bututu, magudanar ruwa, tiyo da kuma ducting
- Supporting or lowering smooth cylindrical loads where clamps or hooks must not mark the surface
- Telecom, mai amfani, offshore and tunnel installation work
Cable Pulling Sock Specifications
Standard specification of Lifet cable pulling socks / wire mesh pulling grips
Selection chart (cable diameter → sock size)
Values are typical for the standard galvanised range. Final capacity depends on cable surface, mesh length and number of layers — please confirm the rating for your application with our engineers before use.
How to Select the Right Cable Pulling Sock
- Measure the outside diameter of the cable, pipe or bundle at the point it will be gripped — not the nominal size. For bundles, yi amfani da diamita gabaɗaya.
- Check the diameter range — a sock must be expanded to grip, so choose a model whose range covers your measured diameter. Too large will slip, kankana ba zai zamewa ba.
- Match the mesh length to the load — longer socks spread the grip and support higher pulling forces; as a rule, use at least 4–5 × the cable diameter of mesh engagement.
- Choose the eye type — single eye for straight pulls, biyu / flexible eye where the line must swivel, rotating eye for long duct runs.
- Consider the surface — for painted, stainless or plastic pipe, choose a PVC or rubber coated mesh to prevent marking.
Shigarwa & Amintaccen Amfani
- Duba raga, ido da ferrule kafin kowane amfani; discard any sock with broken wires, idon da ya lalace ko ya zame.
- Expand the mesh fully and slide it on until the cable end reaches the eye — never pull with the cable only half inserted.
- Ci gaba da ja a layi tare da axis ɗin raga; side loading reduces capacity and can damage the weave.
- Kar a taɓa ƙetare ƙarfin ja da aka ƙididdigewa, and never use a cable pulling sock for overhead lifting unless the model has been rated and marked for lifting use.
- Ajiye bushe da tsabta; wipe and re-check galvanised socks after use in wet or salty environments.
-

Lift sling rigging company produce Double Eye Split Mesh Lace Closing Support Grips
Quality Control at Lift
Abubuwan da aka bayar na Lift Sling Rigging Co., Ltd., Ltd has produced wire rope and mesh rigging in Taizhou, Jiangsu kusan shekaru talatin. Each cable pulling sock is braided from wire we select, ido yana murƙushewa ko murɗa shi zuwa tsayin sarrafawa, kuma samfurori an ɗora su da hujja kafin aikawa. Ana iya shirya rahotannin dubawa kafin jigilar kaya da gwaji na ɓangare na uku akan buƙata.
Tambayoyin da ake yawan yi
What is a cable pulling sock used for?
Yana kama igiya, bututu, rod or duct so it can be pulled with a winch or by hand. The wire mesh tightens as tension rises, which spreads the gripping force along the cable and avoids clamps that could crush or mark it.
How do I choose the correct size?
Measure the true outer diameter of the cable or bundle and pick the model whose range covers it, then choose the mesh length from the pulling load. Our selection chart above gives standard models from 9 mm ku 160 mm.
Single eye or double eye — what is the difference?
A single eye has one braided loop for a straight pull. A double or flexible eye gives two loops (or a swivel point) so the sock can align with the winch line in bends, manholes and long duct runs.
Can the mesh be stainless steel or coated?
Ee. Galvanized waya daidai yake; AISI 304 ko 316 stainless steel is available for corrosive or offshore work, and PVC or rubber coated mesh is available where the cable or pipe surface must not be marked.
Menene ma'anar aminci?
Standard socks are rated at a 5:1 aminci factor a kan karya ƙarfi. Tell us your required pulling load and we will specify the mesh wire diameter and length to suit.
Can you make custom lengths and put our brand on it?
Yes — custom mesh lengths up to 3000 mm, custom eye types, colour coding and your own logo or private label packing are all produced to order at our factory.
Request a Cable Pulling Sock Quotation
Send us your cable diameter, raga tsawon, nau'in ido da nauyin ja da ake buƙata, and our engineers will confirm the correct model and price within one working day.
Waya / WhatsApp: +86 180 6600 2268 Imel: 702461526Adireshin @qq.com: Lifute Industrial Park, Birnin Taizou, Lardin Jiangsu, China
Samfura masu alaƙa
- Waya igiya majajjawa - cikakken kewayon
- Lifting slings and lifting belts
- Cargo nets and lifting nets
- Contact Lifet for a quotation
| Siga | Ƙayyadaddun bayanai |
| Sunan samfur | Kebul na jan safa / igiyoyin waya ja riko / cable pulling grip |
| Kayan abu | Galvanized high tensile karfe waya (AISI 304 / 316 bakin karfe na zaɓi) |
| Tsarin | Double-layer cross-woven tubular mesh with braided or swaged eye |
| raga diamita | 1.5 mm / 2.0 mm / 2.5 mm / 3.0 mm (zaba ta hanyar diamita na USB da kuma ja lodi) |
| Kewayon diamita na USB | 9-16 mm har zuwa 130-160 mm a daidaitattun samfura; manyan girma da aka yi don yin oda |
| raga (safa) tsayi | 300 mm, 450 mm, 600 mm, 900 mm, 1200 mm, 1500 mm; al'ada har zuwa 3000 mm |
| Ido / nau'in kai | Ido ɗaya, ido biyu, m ido, juyawar ido, mata ido |
| Daidaiton ido | Braided rope eye or swaged aluminium ferrule (bakin ciki, low ginawa profile) |
| Karɓar ƙarfi | Model dependent — see selection chart below |
| Safety factor | 5:1 a kan rated karya ƙarfi |
| Zaɓuɓɓukan sutura | A fili galvanized; PVC / rubber coated mesh; coloured coating for coding |
| Yanayin aiki | -40 °C zuwa +120 °C (rufaffiyar sigar zuwa +70 °C) |
| Keɓancewa | Tsawon raga na al'ada, ido na al'ada, buga tambari, marufi masu zaman kansu |
| Asalin | Abubuwan da aka bayar na Lift Sling Rigging Co., Ltd., Ltd - Taizhou, Jiangsu, China |
| Samfura | Kebul Ø kewayon (mm) | Tsawon raga (mm) | Sakin waya Ø (mm) | Ƙarfin ja (kg) |
| Saukewa: CPS-16 | 9–16 | 300 | 1.5 | 750 |
| Saukewa: CPS-25 | 16-25 | 450 | 2.0 | 1,300 |
| Saukewa: CPS-38 | 25–38 | 600 | 2.0 | 1,800 |
| Saukewa: CPS-50 | 38-50 | 700 | 2.5 | 2,500 |
| Saukewa: CPS-75 | 50-75 | 900 | 2.5 | 3,500 |
| Saukewa: CPS-100 | 75–100 | 1200 | 3.0 | 5,000 |
| Saukewa: CPS-160 | 130-160 | 1500 | 3.0 | 8,000 |



