Lift sling rigging company produce Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.
Lifet cable pulling socks — also called wire mesh pulling grips, chaussettes à câble, cable pulling grips or mesh grips — are flexible steel wire mesh sleeves that grip a cable, pipe or duct rod tightly while you pull it. The mesh tightens around the load as tension rises, so a pulling sock needs no clamps, bolts or tools: slide it on, pull, and the grip locks on. Every sock is braided in our own factory from galvanised steel wire, avec un seul oeil, double eye or flexible eye options, for cable diameters from 9 mm à 160 mm.
What Is a Cable Pulling Sock?
A cable pulling sock is a tubular, double-layer woven wire mesh that slips over the end of a cable and grips it by friction alone. The open end of the mesh closes on the cable, the closed end carries a braided eye or swaged eye, and the pulling line is attached to that eye. Because the grip increases with the pull, the sock holds the cable without crushing the insulation, the conductor or the pipe wall.
Typical names for the same tool in different trades: chaussette de tirage de câble, poignée de traction en treillis métallique, cable sock, pulling grip, mesh grip, wire grip, bas de câble, support grip and Kellems-style grip.

How a Wire Mesh Cable Pulling Grip Works
- Slide on — the mesh is expanded and pushed over the cable end. It must be long enough to cover the whole gripping length, pas seulement l'extrémité du câble.
- Grip — as the pulling line tensions the eye, the weave contracts radially. Pulling force is converted into a uniform radial clamping force along the entire mesh length, so the load is spread over a long section of cable instead of one point.
- Release — slacken the line and push the mesh forward; the weave opens and the sock slides off. Aucun outil, no damage to the cable jacket.
The same principle lets a pulling sock be used to lift, hold or support a smooth cylindrical load — pipes, ducts, conduit bundles, rods, cable drums and hoses.
Key Features of Lift Cable Pulling Socks
- Galvanised steel wire mesh — high-tensile, corrosion-resistant wire braided in a double-layer cross weave; AISI 304 / 316 stainless steel available on request.
- Grip increases with load — no clamp, no bolt, no cable deformation; ideal for fragile insulation, lead sheaths, fibre and copper.
- Un seul oeil, double eye or flexible eye — braided rope eye, swaged aluminium ferrule eye, rotating eye and offset eye versions.
- Wide size range — cable diameter 9–160 mm, mesh length 300–1500 mm as standard; longer and larger sizes made to order.
- Optional protective coating — PVC / rubber coated mesh for painted, stainless or polished pipe where surface marking must be avoided.
- OEM and private label — your logo, longueur de maille, eye type and packing; factory-direct pricing and fast lead time from Jiangsu, Chine.
Applications typiques
- Tirer le VG, MV and HV power cables, control and fibre optic cable through ducts and trenches
- Tirer des faisceaux de câbles, wire ropes and rods with cable winches and pullers
- Manutention de tuyaux en acier, Tuyau PVC/PE, conduit, tuyau et conduit
- Supporting or lowering smooth cylindrical loads where clamps or hooks must not mark the surface
- Télécom, utilitaire, offshore and tunnel installation work
Cable Pulling Sock Specifications
Standard specification of Lifet cable pulling socks / wire mesh pulling grips
Selection chart (cable diameter → sock size)
Values are typical for the standard galvanised range. Final capacity depends on cable surface, mesh length and number of layers — please confirm the rating for your application with our engineers before use.
How to Select the Right Cable Pulling Sock
- Measure the outside diameter of the cable, pipe or bundle at the point it will be gripped — not the nominal size. For bundles, utiliser le diamètre total.
- Check the diameter range — a sock must be expanded to grip, so choose a model whose range covers your measured diameter. Too large will slip, trop petit ne glisse pas.
- Match the mesh length to the load — longer socks spread the grip and support higher pulling forces; as a rule, use at least 4–5 × the cable diameter of mesh engagement.
- Choose the eye type — single eye for straight pulls, double / flexible eye where the line must swivel, rotating eye for long duct runs.
- Consider the surface — for painted, stainless or plastic pipe, choose a PVC or rubber coated mesh to prevent marking.
Installation & Utilisation sûre
- Inspecter le maillage, oeil et virole avant chaque utilisation; discard any sock with broken wires, un œil déformé ou une virole glissée.
- Expand the mesh fully and slide it on until the cable end reaches the eye — never pull with the cable only half inserted.
- Gardez la traction alignée avec l'axe du maillage; side loading reduces capacity and can damage the weave.
- Ne dépassez jamais la capacité de traction nominale, and never use a cable pulling sock for overhead lifting unless the model has been rated and marked for lifting use.
- Conserver au sec et propre; wipe and re-check galvanised socks after use in wet or salty environments.
-

Lift sling rigging company produce Double Eye Split Mesh Lace Closing Support Grips
Quality Control at Lift
Ascenseur Sling Rigging Co., Ltd has produced wire rope and mesh rigging in Taizhou, Jiangsu depuis près de trente ans. Each cable pulling sock is braided from wire we select, l'œil est tressé ou embouti à une longueur contrôlée, et les échantillons sont chargés avant expédition. Des rapports d'inspection avant expédition et des tests tiers peuvent être organisés sur demande.
Foire aux questions
What is a cable pulling sock used for?
Il saisit un câble, tuyau, rod or duct so it can be pulled with a winch or by hand. The wire mesh tightens as tension rises, which spreads the gripping force along the cable and avoids clamps that could crush or mark it.
How do I choose the correct size?
Measure the true outer diameter of the cable or bundle and pick the model whose range covers it, then choose the mesh length from the pulling load. Our selection chart above gives standard models from 9 mm à 160 mm.
Single eye or double eye — what is the difference?
A single eye has one braided loop for a straight pull. A double or flexible eye gives two loops (or a swivel point) so the sock can align with the winch line in bends, manholes and long duct runs.
Can the mesh be stainless steel or coated?
Oui. Le fil galvanisé est standard; AISI 304 ou 316 stainless steel is available for corrosive or offshore work, and PVC or rubber coated mesh is available where the cable or pipe surface must not be marked.
Quel est le facteur de sécurité?
Standard socks are rated at a 5:1 facteur de sécurité sur la résistance à la rupture. Tell us your required pulling load and we will specify the mesh wire diameter and length to suit.
Can you make custom lengths and put our brand on it?
Yes — custom mesh lengths up to 3000 mm, custom eye types, colour coding and your own logo or private label packing are all produced to order at our factory.
Request a Cable Pulling Sock Quotation
Send us your cable diameter, longueur de maille, type d'oeil et charge de traction requise, and our engineers will confirm the correct model and price within one working day.
Téléphone / WhatsApp: +86 180 6600 2268 E-mail: 702461526@qq.com Adresse: Parc industriel de Lifute, Ville de Taizhou, Province du Jiangsu, Chine
Produits associés
- Élingues en câble métallique — gamme complète
- Lifting slings and lifting belts
- Cargo nets and lifting nets
- Contact Lifet for a quotation
| Paramètre | Spécification |
| Nom du produit | Chaussette de tirage de câble / poignée de traction en treillis métallique / cable pulling grip |
| Matériel | Fil d'acier galvanisé à haute résistance (AISI 304 / 316 acier inoxydable en option) |
| Structure | Double-layer cross-woven tubular mesh with braided or swaged eye |
| Diamètre du fil de maille | 1.5 mm / 2.0 mm / 2.5 mm / 3.0 mm (sélectionné par diamètre de câble et charge de traction) |
| Plage de diamètre de câble | 9–16 mm jusqu'à 130–160 mm dans les modèles standards; plus grandes tailles sur commande |
| Engrener (chaussette) longueur | 300 mm, 450 mm, 600 mm, 900 mm, 1200 mm, 1500 mm; personnalisé jusqu'à 3000 mm |
| Œil / type de tête | Un seul oeil, double oeil, oeil flexible, oeil tournant, œil décalé |
| Ajustement des yeux | Braided rope eye or swaged aluminium ferrule (mince, profil à faible accumulation) |
| Force de rupture | Model dependent — see selection chart below |
| Facteur de sécurité | 5:1 sur la résistance à la rupture nominale |
| Options de revêtement | Galvanisé ordinaire; PVC / rubber coated mesh; coloured coating for coding |
| Température de travail | −40 °C à +120 °C (versions revêtues pour +70 °C) |
| Personnalisation | Longueur de maillage personnalisée, custom eye, impression de logo, emballage de marque privée |
| Origine | Ascenseur Sling Rigging Co., Ltd — Taizhou, Jiangsu, Chine |
| Modèle | Gamme de Ø de câble (mm) | Longueur de maille (mm) | Ø du fil de maille (mm) | Capacité de traction (kilos) |
| CPS-16 | 9–16 | 300 | 1.5 | 750 |
| CPS-25 | 16–25 | 450 | 2.0 | 1,300 |
| CPS-38 | 25–38 | 600 | 2.0 | 1,800 |
| CPS-50 | 38–50 | 700 | 2.5 | 2,500 |
| CPS-75 | 50–75 | 900 | 2.5 | 3,500 |
| CPS-100 | 75–100 | 1200 | 3.0 | 5,000 |
| CPS-160 | 130–160 | 1500 | 3.0 | 8,000 |



