Катэгорыі прадуктаў

Шкарпэткі для цягання кабеля

Кароткае апісанне:

Lift sling rigging company produce Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.

Steel wire mesh cable pulling socks for cables, pipes and ducts. Cable Ø 9–160 mm, mesh length 300–1500 mm, адно або два вочы. Непасрэдна на заводзе ад кампаніі Lift sling.

Дэталь прадукту

Lift sling rigging company produce Cable Pulling Socks Grip,Wire Mesh Puller Socks Grip,Anti-Slip Single eye Cable Pulling Sock,Galvanized Steel Cable Pulling Grip Socks.

Lifet cable pulling socks — also called wire mesh pulling grips, кабельныя шкарпэткі, cable pulling grips or mesh grips — are flexible steel wire mesh sleeves that grip a cable, pipe or duct rod tightly while you pull it. The mesh tightens around the load as tension rises, so a pulling sock needs no clamps, bolts or tools: slide it on, цягнуць, and the grip locks on. Every sock is braided in our own factory from galvanised steel wire, з адным вокам, double eye or flexible eye options, for cable diameters from 9 мм да 160 мм.

What Is a Cable Pulling Sock?

A cable pulling sock is a tubular, double-layer woven wire mesh that slips over the end of a cable and grips it by friction alone. The open end of the mesh closes on the cable, the closed end carries a braided eye or swaged eye, and the pulling line is attached to that eye. Because the grip increases with the pull, the sock holds the cable without crushing the insulation, the conductor or the pipe wall.

Typical names for the same tool in different trades: шкарпэтку для нацягвання кабеля, счапленне з драцяной сеткі, кабельны шкарпэтку, pulling grip, mesh grip, wire grip, кабельны панчоха, support grip and Kellems-style grip.

Cable Pulling Socks
Lift sling rigging company produce Cable Pulling Socks

How a Wire Mesh Cable Pulling Grip Works

  • Slide on — the mesh is expanded and pushed over the cable end. It must be long enough to cover the whole gripping length, not just the cable tip.
  • Grip — as the pulling line tensions the eye, the weave contracts radially. Pulling force is converted into a uniform radial clamping force along the entire mesh length, so the load is spread over a long section of cable instead of one point.
  • Release — slacken the line and push the mesh forward; the weave opens and the sock slides off. Без інструментаў, no damage to the cable jacket.

The same principle lets a pulling sock be used to lift, hold or support a smooth cylindrical load — pipes, ducts, conduit bundles, rods, cable drums and hoses.

Key Features of Lift Cable Pulling Socks

  • Galvanised steel wire mesh — high-tensile, corrosion-resistant wire braided in a double-layer cross weave; AISI 304 / 316 stainless steel available on request.
  • Grip increases with load — no clamp, no bolt, no cable deformation; ideal for fragile insulation, lead sheaths, fibre and copper.
  • Адзінае вока, double eye or flexible eye — braided rope eye, swaged aluminium ferrule eye, rotating eye and offset eye versions.
  • Wide size range — cable diameter 9–160 mm, mesh length 300–1500 mm as standard; longer and larger sizes made to order.
  • Optional protective coating — PVC / rubber coated mesh for painted, stainless or polished pipe where surface marking must be avoided.
  • OEM and private label — your logo, даўжыня сеткі, eye type and packing; factory-direct pricing and fast lead time from Jiangsu, Кітай.

Тыповыя прымянення

  • Выцягванне ЛЖ, MV and HV power cables, control and fibre optic cable through ducts and trenches
  • Выцягванне пучкоў кабеляў, wire ropes and rods with cable winches and pullers
  • Апрацоўка сталёвых труб, PVC/PE pipe, трубаправод, шланг і паветравод
  • Supporting or lowering smooth cylindrical loads where clamps or hooks must not mark the surface
  • Тэлекам, карыснасць, offshore and tunnel installation work

Cable Pulling Sock Specifications

Standard specification of Lifet cable pulling socks / wire mesh pulling grips

Selection chart (cable diameter → sock size)

Values are typical for the standard galvanised range. Final capacity depends on cable surface, mesh length and number of layers — please confirm the rating for your application with our engineers before use.

How to Select the Right Cable Pulling Sock

  • Measure the outside diameter of the cable, pipe or bundle at the point it will be gripped — not the nominal size. For bundles, use the overall diameter.
  • Check the diameter range — a sock must be expanded to grip, so choose a model whose range covers your measured diameter. Too large will slip, too small will not slide on.
  • Match the mesh length to the load — longer socks spread the grip and support higher pulling forces; as a rule, use at least 4–5 × the cable diameter of mesh engagement.
  • Choose the eye type — single eye for straight pulls, двайны / flexible eye where the line must swivel, rotating eye for long duct runs.
  • Consider the surface — for painted, stainless or plastic pipe, choose a PVC or rubber coated mesh to prevent marking.

Ўстаноўка & Бяспечнае выкарыстанне

  • Агледзіце сетку, вачэй і наканечнік перад кожным выкарыстаннем; discard any sock with broken wires, дэфармаванае вока або саслізнуў наканечнік.
  • Expand the mesh fully and slide it on until the cable end reaches the eye — never pull with the cable only half inserted.
  • Трымайце цягу на адной лініі з воссю сеткі; side loading reduces capacity and can damage the weave.
  • Ніколі не перавышайце намінальную цягаздольнасць, and never use a cable pulling sock for overhead lifting unless the model has been rated and marked for lifting use.
  • Захоўваць у сухім і чыстым выглядзе; wipe and re-check galvanised socks after use in wet or salty environments.
  • Double Eye Split Mesh Lace Closing Support Grips
    Lift sling rigging company produce Double Eye Split Mesh Lace Closing Support Grips

Quality Control at Lift

Lift Sling Rigging Co., Ltd has produced wire rope and mesh rigging in Taizhou, Цзянсу на працягу амаль трыццаці гадоў. Each cable pulling sock is braided from wire we select, the eye is braided or swaged to a controlled length, і ўзоры праходзяць праверку перад адпраўкай. Па запыце могуць быць арганізаваны справаздачы аб інспекцыі перад адгрузкай і выпрабаванні трэціх асоб.

Часта задаюць пытанні

What is a cable pulling sock used for?

Ён захоплівае кабель, труба, rod or duct so it can be pulled with a winch or by hand. The wire mesh tightens as tension rises, which spreads the gripping force along the cable and avoids clamps that could crush or mark it.

How do I choose the correct size?

Measure the true outer diameter of the cable or bundle and pick the model whose range covers it, then choose the mesh length from the pulling load. Our selection chart above gives standard models from 9 мм да 160 мм.

Single eye or double eye — what is the difference?

A single eye has one braided loop for a straight pull. A double or flexible eye gives two loops (or a swivel point) so the sock can align with the winch line in bends, manholes and long duct runs.

Can the mesh be stainless steel or coated?

так. Ацынкаваны дрот стандартны; AISI 304 або 316 stainless steel is available for corrosive or offshore work, and PVC or rubber coated mesh is available where the cable or pipe surface must not be marked.

Што такое каэфіцыент бяспекі?

Standard socks are rated at a 5:1 каэфіцыент трываласці на разрыў. Tell us your required pulling load and we will specify the mesh wire diameter and length to suit.

Can you make custom lengths and put our brand on it?

Yes — custom mesh lengths up to 3000 мм, custom eye types, colour coding and your own logo or private label packing are all produced to order at our factory.

Request a Cable Pulling Sock Quotation

Send us your cable diameter, даўжыня сеткі, eye type and required pulling load, and our engineers will confirm the correct model and price within one working day.

Тэлефон / WhatsApp: +86 180 6600 2268 Электронная пошта: 702461526@qq.com Адрас: Індустрыяльны парк Ліфутэ, Горад Тайчжоу, Правінцыя Цзянсу, Кітай

Спадарожныя тавары

  • Стропы канатныя — поўны асартымент
  • Lifting slings and lifting belts
  • Cargo nets and lifting nets
  • Contact Lifet for a quotation
Параметр Спецыфікацыя
Назва прадукту Шкарпэтку для цягання троса / счапленне з драцяной сеткі / cable pulling grip
Матэрыял Дрот з ацынкаванай сталі высокай трываласці (AISI 304 / 316 з нержавеючай сталі па жаданні)
Структура Double-layer cross-woven tubular mesh with braided or swaged eye
Дыяметр сеткі 1.5 мм / 2.0 мм / 2.5 мм / 3.0 мм (selected by cable diameter and pulling load)
Дыяпазон дыяметраў кабеляў 9–16 mm up to 130–160 mm in standard models; вялікія памеры на заказ
Сетка (шкарпэтку) даўжыня 300 мм, 450 мм, 600 мм, 900 мм, 1200 мм, 1500 мм; звычай да 3000 мм
Вока / тып галавы Адзінае вока, падвойнае вока, flexible eye, rotating eye, зрушэнне вачэй
Падганянне вачэй Braided rope eye or swaged aluminium ferrule (thin, low build-up profile)
Трываласць на разрыў Model dependent — see selection chart below
Каэфіцыент бяспекі 5:1 на намінальную трываласць на разрыў
Варыянты пакрыцця Звычайны ацынкаваны; PVC / rubber coated mesh; coloured coating for coding
Працоўная тэмпература ад −40 °C да +120 °C (версіі з пакрыццём да +70 °C)
Налада Нестандартная даўжыня сеткі, custom eye, прынт лагатыпа, упакоўка прыватнай маркі
Паходжанне Lift Sling Rigging Co., Ltd — Тайчжоу, Цзянсу, Кітай

 

мадэль Дыяметр кабеля Ø (мм) Даўжыня сеткі (мм) Драцяная сетка Ø (мм) Цягавая здольнасць (кг)
ЦПС-16 9–16 300 1.5 750
ЦПС-25 16–25 450 2.0 1,300
ЦПС-38 25–38 600 2.0 1,800
ЦПС-50 38–50 700 2.5 2,500
ЦПС-75 50–75 900 2.5 3,500
ЦПС-100 75–100 1200 3.0 5,000
ЦПС-160 130–160 1500 3.0 8,000

Пакіньце сваё паведамленне

Пракруціць да пачатку